Heart Rate Inc. 1411 E. Wilshire Ave. Santa Ana, CA 92705 1.800.237.2271
(2) 9/16” wrenches Drill Pencil
Tape Measure 3/16 drill bit
Qty 2 3/8-16 x 4” Hex Head Bolt
Qty 4 3/8”-16 x 1” Hex Head Bolt
Qty 8 3/8” Washer
Qty 5 5/16 x 1 1/2” Hex Head Lag Screw
QTY 5, 5/16 x 1 1/2 “ Lag Screw Anchor
Qty 5 5/16” Washer
Page 1
WALL MOUNTING INSTRUCTIONS Step 4.
Attach wall mount bracket to the VersaClimber, using (2) bolts.
Step 1.
Determine if you will be securing VersaClimber into
a concrete wall or a standard drywall wall with wood
studs. NOTE: The wall mounting hardware
provided is for general installation into Concrete
or Drywall with wood studs. Depending on the
wall type or floor, additional hardware may be
required. If this is the case, seek proper hard-
ware and installation recommendation.
Step 2. To mount the bracket take one of the screws and run it through
If securing to a cement wall, go to Step #8. the bracket and post and apply locknut. Next, apply the other bolt
For securing to drywall with wood studs continue to and nut, securing 2 bolts and nuts with 9/16” wrenches.
next step #3.
Step 3.
A 2”x6” wood board is recommended. Make the
length of 2”x6” board long enough to span across at
least two vertical wall studs.
2”x6” wood board
Slide post under the wall mount bracket. With screw and
Cover at least (2)
washer run through the post into the wall mount bracket and
wall studs apply the washer and locknut, leave loose and apply the other
Wall studs
3 bolts/nuts. Then tighten.
NOTE: The number of attached VersaClimber’s
determines the length of the 2”x6” board. For
example, two VersaClimbers mounted requires a
minimum board length of 6’ long, that is properly
secured to the wall.
BEFORE MOUNTING TO WALL,
CENTERED ON WALL BRACKET.
75” (190.5 cm)
From centerline of wall
bracket to the floor.
38” 96.5 cm
These slots allow movement forward
From wall to the front 2 bolt holes
and backward if adjustments are
on the base of VersaClimber post. needed from the wall.
Page 2
Center line.
38” from wall can vary depending
on wall, baseboards and / or
where the bracket is positioned.
Find the center line 75 inches
up from the floor.
75 inches
(190.5 cm)
38 inches from wall
(96.5 cm)
The front base holes of VersaClimber should be
approx 38 inches in front of wall. Distance can vary
Center line. depending on wall, baseboards and or where the
bracket is positioned.
Step 6.
Mark the bracket holes on the center line. Remove the
VersaClimber and carefully place to the side. Drill 3 pilot
holes through the 2x6 wood support using 3/16” drill.
Step 5.
With wall bracket attached, stand the VersaClimber up and
rest the bracket against the piece of 2x6 board that has been
securely mounted to the wall. Place the holes of the bracket
on the center line, then mark the bracket holes.
The two that go into the ground, may or
may not be needed. Our hardware may
not accommodate your wall, please
consult with a contractor.
Step 7.
Place VersaClimber back into place and align the 3 holes.
Secure with the three 5/16” lag bolts and washers provided.
Firmly tighten down lag bolts. Next go to step 13.
Page 3
For cement walls follow steps 8-12 Step 13.
The VersaClimber is now secured to the wall. You can adjust
the VersaClimber closer or farther from the wall to avoid
Step 8. small obstructions. The closer the VersaClimber is to the wall
Mounting VersaClimber to a cement wall. Mark a line horizontally the more stable it will be.
75 inches from the floor.
Step 9.
Attach the brackets to VersaClimber using the four bolts, washers
and nuts provided. Center the four bolts to allow adjustment
forward and backwards.
Step 10.
Stand the VersaClimber and rest the attached wall mount bracket
on the center line you have marked on the wall. The front base
holes on the VersaClimber should be 38 inches from the wall. This
distance may vary depending on the wall, base boards, and or
where the bracket is positioned.
Adjust the VersaClimber if necessary. Determine if the base
Step 11. needs to be secured to the floor for extra stability. Climb onto
Mark the three holes on the centerline. Remove the VersaClimber the VersaClimber to see if the base moves. If you want to
and carefully place to the side. Drill the three holes using 1/2” secure to the floor, continue to next step.
cement dril bit at least 1 inch deep.
Step 14.
Step 12. After you have adjusted the bracket mark the two front base
Tap in the three lag shields supplied. Place the VersaClimber back holes on the floor.
into place aligning the three holes and secure with three 5/16” lag
bolts pluse washers supplied. Step 15.
You must remove the VersaClimber from the wall in order to
drill the holes into the floor. Carefully set VersaClimber off to
the side. If you have wood floor, drill two holes with 3/16” drill
at least 1 inch deep.
If you have a cement floor, drill two holes with 1/2” cement
drill at least 1” deep, and tap in two lag shields supplied.
NOTE: Step 16.
The two that go into the ground, may or Replace and secure the VersaClimber back to the wall
making sure bottom holes are aligned. Secure base using
may not be needed. Our hardware may
washers supplied. Make sure all bolts and lags are tight.
not accommodate your wall, please
consult with a contractor.
Page 4
Questions or Comments please call us: 1.800.237.2271 / 714.850.9716
Email: [email protected]
