(cid:0) (cid:1) (cid:2) (cid:2) (cid:3) (cid:4) (cid:5) (cid:6) (cid:7) (cid:8) (cid:9) (cid:9) (cid:10) (cid:8) (cid:8)
of Cables
IMPORTANT:Cables are
wear items.It is your
responsibility to prevent
unexpected breakage.
Cable inspection should
be performed daily.
Inspect all cables, the
nylon coating on all
cables,and the area
near the fitting at each
end of each cable.
Replaceanydamaged or
worncableimmediately.
Do not allow the machine
to be used until damaged
or worn cables are
replaced.Using or allowing
a machine to be used
with a suspect cable can
result in serious injury.See
Owner’s Manual for more
information.
2
(cid:11) (cid:12) (cid:13) (cid:14) (cid:12) (cid:15) (cid:16) (cid:17)(cid:18) (cid:12) (cid:19)(cid:20)(cid:15) (cid:21) (cid:22) (cid:23) (cid:24)(cid:12) (cid:25) (cid:26) (cid:13) (cid:18) (cid:26) (cid:13)(cid:27) (cid:20)(cid:28) (cid:26)
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT.
Inspect equipment before each workout. Check that all nuts, bolts, screws and pop pins
are in place and fully tightened. Also, before use, check cables for sign of wear. Replace all
worn parts immediately. Never use machine if any parts are damaged or missing.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
Keep clear of the cables and all moving parts when machine is in use.
Always make sure all Snap Links are closed when doing cable/pulley/strap exercises.
Exercise with care. Perform your exercises at a smooth moderate pace; never perform jerky
or uncoordinated movements that may cause injury.
It is recommended that you workout with a training partner.
Do not allow children or minors to play on or around this equipment.
If unsure of proper use of equipment, call your local Body-Solid distributor or the
Body-Solid customer service center at 1-800-556-3113.
WARNING: Consult your physician before starting your exercise program. For your own
safety, do not begin any exercise program without proper instruction.
3
When using exercise equipment,
you should always take basic
precautions including the
following:
Read all instructions before using the PCCO90X.
These instructions are written to ensure your safety
and to protect the unit.
4
(cid:29)
#
(cid:30)
%
(cid:31)
,
(cid:30)
+ -(cid:31)
!
"
"
.
# (cid:30) $ " % (cid:31) & ’ % ( " & )% * " )’ ( ! (cid:30) # + "
•
Do not allow children on or near the equipment.
Use the equipment only for its intended purpose
as described in this guide. Do not use accessory
attachments that are not recommended by the
manufacturer. Such attachments might cause serious
injuries.
Wear proper excercise clothing and shoes for your
workout, no loose clothing.
Keep hands, limbs, loose clothing, and long hair well
out of the way of all moving parts
Use care when getting on or off the unit.
Do no overexert yourself or work to exhaustion.
If you feel any pain or abnormal symptoms, stop your
workout immediately and consult your physician.
Never operate unit when it has been dropped or
damaged. Return the equipment to a service center
for examination and repair.
Never drop or insert objects into any opening in the
equipment.
Always check the unit and its cables before each use.
Make sure that all fasteners and cables are secure
and in good working condition.
Do not use the equipment outdoors or near water.
/
The PCCO90X is designed for your enjoyment. By
following these precautions and using common sense,
you will have many safe and pleasurable hours of
healthful exercise with your Powerline Cable
Crossover Machine.
After assembly, you should check all functions to
ensure correct operation. If you experience problems,
fi rst recheck the assembly instructions to locate any
possible errors made during assembly. If you are un-
• able to correct the problem, call the dealer from whom
• you purchased the machine or call 1-800-556-3113 for
the dealer nearest you.
• Please use this Owner’s Manual to make sure that
all parts have been included in your shipment. When
• ordering parts, you must use the part number and
description from this Owner’s Manual. Use only
• Powerline by Body Solid replacement parts when
• servicing this machine. Failure to do so will void your
• warranty and could result in personal injury.
• For information about product operation or
service, check out the offi cial Powerline website
at www.bodysolid.com or contact an authorized
• Powerline dealer or a Powerline factory-authorized
service company or contact Body-Solid customer
• service at one of the following:
• Phone: 1-708-427-3555
Email: [email protected]
• Before beginning assembly, please take the time to
read the instructions thoroughly. Or write to: Body-Solid, Inc.
• Read each step in the assembly instructions and Service Department
follow the steps in sequence. Do not skip ahead. If 1900 S. Des Plaines Ave.
you skip ahead, you may learn later that you have Forest Park, IL 60130 USA
to disassemble components and that you may have
damaged the equipment Retain this Owner’s Manual for
• Assemble and operate the PCCO90X on a solid, level furture reference. Part numbers
surface. Locate the unit a few feet from the walls or are required when ordering parts.
furniture to provide easy access.
The basic tools that you must obtain before assembling Read all “Notes” on each page before beginning each step.
the PCCO90X include but are not limit to:
While you may be able to assemble the PCCO90X using the
• Standard Wrench Set illustrations only, important safety notes and other tips may be
included in the text.
Some pieces may have extra holes that you will not use. Use
• Adjustable Wrench only those holes indicated in the instructions and illustrations.
• Standard / Metric Allen Key Set NOTE: With so many assembled parts, proper
alignment and adjustment is critical. While
Installation Requirements tightening the nuts and bolts, be sure to leave
room for adjustments.
Follow these installation requirements when assembling
the PCCO90X: NOTE: The bottles that are marked “Poison” is your
touch up paint. Keep away from children.
Set up the PCCO90X on a solid, fl at surface. A smooth,
fl at surface under the machine helps keep it level.
Provide ample space around the machine. Open space
around the machine allows for easier access.
For aesthetic purposes, insert all bolts in the same
direction unless specifi ed (in text or illustrations) to do
otherwise.
Leave room for adjustments. Tighten fasteners such as
bolts, nuts, and screws so the unit is stable, but leave
room for adjustments. Do not fully tighten fasteners until
instructed in the assembly steps to do so.
Fill out and mail the warranty card.
If you need to order replacement parts please be
prepared to provide the following information
when contacting us so that we can assist you better.
2. Place of Purchase
3. Serial Number (S/N)
4. Part # and Description
: Obtain assistance! If you feel like you can’t
assemble the PCCO90X by yourself then do
not attempt to do so as this could result in
before proceeding with the following steps.
5
6
(cid:21)(cid:1)(cid:44)(cid:12)(cid:55)(cid:1)(cid:44)(cid:13)
(cid:151)(cid:168)(cid:119)(cid:137)(cid:191)(cid:134)(cid:174)(cid:122)(cid:134)(cid:174)(cid:62)(cid:80)(cid:176)(cid:184)(cid:62)(cid:129)(cid:174)(cid:168)(cid:122)(cid:197)(cid:94)(cid:152)
Part #1 M12X75mm hex head bolt QTY. 10
Part #2 M12X70mm hex head bolt QTY. 2
Part #3 M10X75mm hex head bolt QTY. 2
Part #4 M10X40mm hex head bolt QTY. 6
Part #5 M12 nylon lock nut QTY. 12
(cid:147)(cid:147)
(cid:136)(cid:152)(cid:86)(cid:133)
7
(cid:21)(cid:1)(cid:44)(cid:12)(cid:55)(cid:1)(cid:44)(cid:13)
(cid:151)(cid:168)(cid:119)(cid:137)(cid:191)(cid:134)(cid:174)(cid:122)(cid:134)(cid:174)(cid:62)(cid:80)(cid:176)(cid:184)(cid:62)(cid:129)(cid:174)(cid:168)(cid:122)(cid:197)(cid:94)(cid:152)
HARDWARE ILLUSTRATION CONT.
Part #6 M10 nylon lock nut QTY. 8
Part #7 1/2” nylon lock nut QTY. 6
Part #8 M12 washer QTY. 2
Part #9 50X50mm end cap QTY. 4
Part #10 60X50mm nylon bushing QTY. 4
(cid:147)(cid:147)
(cid:136)(cid:152)(cid:86)(cid:133)
8
(cid:21)(cid:1)(cid:44)(cid:12)(cid:55)(cid:1)(cid:44)(cid:13)
(cid:151)(cid:168)(cid:119)(cid:137)(cid:191)(cid:134)(cid:174)(cid:122)(cid:134)(cid:174)(cid:62)(cid:80)(cid:176)(cid:184)(cid:62)(cid:129)(cid:174)(cid:168)(cid:122)(cid:197)(cid:94)(cid:152)
HARDWARE ILLUSTRATION CONT.
Part #11 1” round end cap QTY. 4
Part #12 110mm pulley QTY. 8
Part #13 50X50mm foot cap QTY. 6
Part #14 8mm snap link QTY. 2
Part #15 50mm rubber cushion QTY. 2
Part #17 5/8” pulley spacer QTY. 2
(cid:147)(cid:147)
(cid:136)(cid:152)(cid:86)(cid:133)
9
vertical frame base frame l-bracket
[2pcs] [2pcs] [2pcs]
weight frame connecting bracket right support bracket
[2pcs] [2pcs] [1pcs]
left support bracket mid pulley holder pulley holder
[1pcs] [2pcs] [4pcs]
cross beam crossover handles
[1pcs] [2pcs]
10
11
IN THE SEQUENCE THAT THEY ARE PRESENTED.
finger tighten all hardware first in this step. wrench tighten at the
end of this step. some components may be PRE-ASSEMBLED.
nylon lock nuts will not fully screw onto bolts, must wrench tighten.
1A. insert a foot cap onto each end of both base
frames (B) using a total of
6 - (#13) 50X50mm foot cap
1B. attach a pulley holder (I) to each base frame (B)
using a total of:
2 - (#7) 1/2” nylon lock nut
1C. insert a nylon bushing into the top and bottom
openings of both weight frames (D) using a total of:
4 - (#10) 60X50mm nylon bushing
1D. insert a end cap into the front openings of both
weight frames (D) using a total of
2 - (#9) 50X50mm end cap
1E. insert a round end cap into the left and right
openings of both weight frames (D) using a total of:
4 - (#11) 1” round end cap
1F. insert rubber cushion onto the lower lip of both
weight frames (D) using a total of:
2 - (#15) 50mm rubber cushion
1G. attach a mid pulley holder (H) to each weight
frame (D) using a total of:
2 - (#7) 1/2” nylon lock nut
12
Above shows STEP 1
assembled and completed
13
IN THE SEQUENCE THAT THEY ARE PRESENTED.
finger tighten all hardware in this step. DO NOT wrench tighten
until the last step. some components may be PRE-ASSEMBLED.
nylon lock nuts will not fully screw onto bolts, must wrench tighten.
2A. first attach a vertical frame (A) to each base frame (B)
using a total of:
2 - (#2) M12X70mm hex head bolt
2 - (#8) M12 washer
2 - (#5) M12 nylon lock nut
2B. second attach a l-bracket (C) to each vertical frame (A)
and then to each base frame (B) using a total of:
2 - (#1) M12X75mm hex head bolt
2 - (#5) M12 nylon lock nut
2C. insert a end cap into each top opening of vertical
frame (A) using a total of:
2 - (#9) 50X50mm end cap
2D. slide an assembled weight frame (D) onto each
vertical frame (A).
2E. attach a pulley holder (I) to left support bracket (G)
and right support bracket (F) using a total of:
2 - (#7) 1/2” nylon lock nut
14
left shows STEP 2
assembled and complete
15
IN THE SEQUENCE THAT THEY ARE PRESENTED.
finger tighten all hardware in this step. DO NOT wrench tighten
until the last step. some components may be PRE-ASSEMBLED.
nylon lock nuts will not fully screw onto bolts, must wrench tighten.
3A. attach cross beam (J) to the vertical frame (A) on the
left side using left support bracket (G) and a
connecting bracket (E) using a total of:
4 - (#1) M12X75mm hex head bolt
4 - (#5) M12 nylon lock nut
3B. attach cross beam (J) to the vertical frame (A) on the
right side using right support bracket (F) and a
connecting bracket (E) using a total of:
4 - (#1) M12X75mm hex head bolt
4 - (#5) M12 nylon lock nut
16
left shows STEP 3
assembled and complete
17
IN THE SEQUENCE THAT THEY ARE PRESENTED.
this step is intended to show you where the pulleys need to be installed
and what hardware you will need to install them. however, you must
install the pulleys the same time you route the cables which can be
found on the next step
4A. a pulley will be attached to both of the two pulley
holders (I) at the base of your PCCO90X using a
total of:
2 - (#12) 110mm pulley
2 - (#4) M10X40mm hex head bolt
2 - (#6) M10 nylon lock nut
4B. a pulley will be attached to both of the two mid pulley
holders (H) attached to the weight frames (D) using a
total of:
2 - (#12) 110mm pulley
2 - (#4) M10X40mm hex head bolt
2 - (#6) M10 nylon lock nut
4C. a pulley will be attached to both of the two mid pulley
holders (H) at the top of your PCCO90X using a
total of:
2 - (#12) 110mm pulley
2 - (#4) M10X40mm hex head bolt
2 - (#6) M10 nylon lock nut
4D. a pulley will be attached in between the connecting
brackets (E) and left support bracket (G) and right
support bracket (F) using a total of:
2 - (#12) 110mm pulley
2 - (#17) 5/8” pulley spacer
2 - (#3) M10X75mm hex head bolt
2 - (#6) M10 nylon lock nut
18
left shows STEP 4
assembled and complete
19
IN THE SEQUENCE THAT THEY ARE PRESENTED.
this step is intended to show you where the pulleys need to be installed
and what hardware you will need to install them. however, you must
install the pulleys the same time you route the cables which can be
found on the next step
5A. left side cable (5170mm, #16) - (L1), install and route
the cable around the pulley and up to (L2). (L2), install
and route the cable around the pulley and then down
to (L3). (L3), install and route the cable around the
pulley and then up to (L4). (L4), install and the route
the cable around the final pulley to complete the left
side cable routing.
5B. right side cable (5170mm, #16) - (R1), install and route
the cable around the pulley and up to (R2). (R2), install
and route the cable around the pulley and then down
to (R3). (R3), install and route the cable around the
pulley and then up to (R4). (R4), install and the route
the cable around the final pulley to complete the right
side cable routing.
5C. attach a snap link followed by a crossover handle (K)
to the left and right side cable at L1 and R1 using a
total of:
2 - (#14) 8mm snap link
20
below shows STEP 5 R2
assembled and complete
l2 l4
l3
l1
21
22
23
please write your serial number in the boxes below
Body-Solid ®
11990000 SS.. DDeess PPllaaiinneess AAvvee..
HHoouurrss:: MM--FF 88::3300 -- 55::0000 CCSSTT
www.bodysolid.com
c Copyright 2011. Body-Solid. All rights reserved. Body-Solid reserves the right to change design and specifications when we feel it will improve the product.
Body-Solid machines maintain several patented and patent pending features and designs. All rights reserved on all design patents and utility patents.
24
